塑料破碎機維護與保養

塑料破碎機維護與保養Plastic crusher maintenance and repair

塑料破碎機維護與保養
塑料破碎機維護與保養1、定期檢查塑料破碎機皮帶是否松弛，及時調緊。

塑料破碎機維護與保養2、**次啟動前，應先**機室所剩余的碎料，減少啟動阻力。應定期打開慣性罩和皮帶輪罩，**法蘭盤下方出灰口，因塑料破碎機室排出粉料進入轉軸軸承。
塑料破碎機維護與保養3、更換刀具時，動刀與定刀之間的間隙:20HP以上破碎機0.8MM為佳，20HP以下的破碎機0.5MM為佳?；厥樟显奖。g隙可適當調大。
4、為保證刀具切口的鋒利度，應常檢查刀具，保證其鋒利度，減少由于刀鋒鈍缺而引起其它部件的不必要損壞。

5、應把塑料破碎機安置通風位置，保證電機工作熱量散發，延長其壽命。


6、定期檢查刀具螺絲，全新塑料破碎機使用1小時后，用工具緊固動刀，定刀的螺絲，加強刀片與刀架間的固定性。

7、機器應保持良好接地。

8、應定期對軸承加注潤滑油，保證軸承間的潤滑性。

Plastic crusher maintenance and repair
Plastic crusher maintenance and maintenance 1, regular inspection of plastic crusher belt is loose, timely tightening.

Plastic crusher maintenance and maintenance 2, the second start, you should first clear the remaining pieces of the machine room to reduce the starting resistance. Should always open the inertia hood and pulley cover, remove the flange below the gray mouth, because the plastic crusher room discharge powder into the shaft bearings.
Plastic crusher maintenance and maintenance 3, the replacement of the tool, the knife and the knife between the gap: 20HP crusher 0.8MM better, 20HP below the crusher 0.5MM is better. The thinner the recovered material, the gap can be properly adjusted.
4, in order to ensure the sharpness of the cutter incision, should always check the tool to ensure its sharpness, reduce the blade blunt caused by other parts of the unnecessary damage.

5, the plastic crusher should be placed ventilation position to ensure that the motor heat dissipation, to extend its life.


6, regularly check the tool screw, the new plastic crusher use 1 hour later, with a tool to tighten the knife, set the screw, to strengthen the blade and the fixed between the knife.

7, the machine should be kept well grounded.

8, should be regularly filling the bearing lubricating oil to ensure the lubrication between the bearings.